Reparieren Bathtub Spa Jets

Jets in diesem Spa-Stil Wanne stürzen das Wasser. Foto: Jacuzzi

Wenn Ihre Badewannen-Whirlpool-Düsen plötzlich nicht mehr funktionieren, führen Sie die folgenden Schritte aus:

1Prüfen Sie den Schutzschalter der Schalttafel, ob er ausgelöst hat. Wenn dies der Fall ist, setzen Sie es zurück.

2Wenn dies nicht das Problem ist, konsultieren Sie in Ihrem Benutzerhandbuch, um zu sehen, ob die Pumpe einen "oberen manuellen Rückstellwert" oder einen separaten Schutzschalter am Gerät hat. Wenn es eine dieser Möglichkeiten hat, versuchen Sie es zurückzusetzen.

3Spa-Jets funktionieren immer noch nicht? Schalten Sie den Stromkreis des Whirlpools aus und rufen Sie eine Reparaturperson an. Das Problem könnte von einem losen Draht zu einem defekten Schwimmerschalter zu einer schlechten Pumpe sein. (Wenn die Reparaturperson ankommt, vergewissern Sie sich, dass Sie wissen, dass Sie die Schaltung ausgeschaltet haben.)

FAQ - 💬

❓ Can you replace spa bath jets?

👉 To replace spa jets, you'll need to drain the water from the tub, remove the existing jets, and screw in new jets that fit your tub. You can usually buy new jets from the same company you purchased the tub from. If you're unable to do this, look for some at your local home improvement store.

❓ Can you replace jets in a Jacuzzi bathtub?

👉 Yes. You can replace jet tub fixtures, and it's actually fairly easy.

❓ Are hot tub jets universal?

👉 Many styles of hot tub jets are interchangeable as long as they are the same size. Most jets can be easily removed by turning them to the left and then they will pop right out.

❓ Why are the jets on my bath tub not working?

👉 If there is too little water, air could be working its way into the system through the jets. If you've checked your filter, water level, and the issue persists, you may have a clog in the line, or your pump is simply reaching the end of its lifetime and should be repaired or replaced.

❓ How are spa jets measured?

👉 0:273:13Identifying Hot Tub Jets.

❓ Why do spa jets pop out?

👉 In addition to killing microbes and dissolving organic material, chlorine causes the plastic in the jet bodies to become brittle. Brittle plastic breaks, which is why the jets pop out of the tub wall.

❓ Can I turn my bath into a jacuzzi?

👉 The Jet Bath Spa hangs over the edge of your tub, and the dual jet attachment works underneath the water to bubble your bath into a full-on whirlpool.

❓ How can I tell what type of jet is on my hot tub?

👉 0:273:13Identifying Hot Tub Jets.

❓ How do you tell what kind of jetted tub you have?

👉 Identifying Your Bath or Whirlpool Model

1. For soaking baths, whirlpools, and air baths (BubbleMassage™), the model number with manufacturing date or the serial number are the best methods for identifying the product.
2. The model number and serial number are printed on a white or silver label.

❓ How do I know what model my jetted tub is?

👉 The model and serial number is located in three places:

1. On a label located on the back page of your Operating/Installation Instructions. (With the warranty information)
2. On a white label located on the bath vessel near the pump/motor.
3. On the shell under the suction cover. (Rectangular cover/filter inside of bath)

❓ How do I make my spa jets stronger?

👉 0:221:39Tips to Increase Jet Pressure in your Hot Tub

❓ How do you remove a hot tub jet from the shell?

👉 Removing and replacing the jet body from the shell of the spa, for resealing or replacement, can be accomplished with one specific wrench, made specifically for your spa or hot tub jet. Spa jet tools or spa wrenches are important to make removal easier, without damaging soft plastic edges.

❓ How do I clean the Jets on my spa?

👉 The next step involves soaking of the jet units in vinegar and water. The vinegar solution will help removed minerals that have deposited on the spa’s components. Once the jets have been removed, place them in a bucket filled with vinegar and water. Allow the jets to soak overnight.

❓ What to do if your hot tub jets are not working?

👉 First, Turn Off the Power. While it can be a shock to discover that your beloved hot tub's jets are not functioning, nothing can prepare you for making accidental contact with the high voltage of a hot tub. Therefore, before you start any type of troubleshooting, be sure to power off your hot tub at the breaker box.

❓ Can I replace my bathtub jets while water is still in it?

👉 It is not safe to replace the jets while water is still in the tub. Drain all water out of the tub before working on your jets. To drain your tub, first turn off the spa’s circuit breaker. Then, remove the front panel of your tub and find the hose spigot. Attach a garden hose to the spigot and drain the water out of the tub. [1]

---

Autor Des Artikels: Alexander Schulz. Unabhängiger Konstrukteur und technischer Experte. Arbeitserfahrung in der Baubranche seit 1980. Fachkompetenz in den Richtungen: Bau, Architektur, Design, Hausbau.

---